- #Darkside cc gen v1 how to#
- #Darkside cc gen v1 install#
- #Darkside cc gen v1 zip file#
- #Darkside cc gen v1 driver#
- #Darkside cc gen v1 Patch#
In configuration_adv.h uncomment line 148 #define Z_DUAL_STEPPER_DRIVERS as following: #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false #define INVERT_X_DIR false // for Mendel set to false, for Orca set to true Please read following instruction to change the Configuration.h and configuration_adv.h file according to your hardware situation:Ī)If you connect MKS Gen/Base board with two Z axis servo motors, please make following changes, In above Marline folder, there is Configuration.h file which defines some important hardware config setting values. Unzip above file, you will see a folder called “Marlin” Step 5)Download Ramps1.4 board Marlin firmware as per your LCD screen type. In Tools->Port select the COM port which associated with Arduino Mega2560(see picture below) Step 4) In Arduino IDE->Tools->Board select Arduino Mega 2560:
#Darkside cc gen v1 zip file#
Then, in Arduino IDE ->Sketch->Include Library->Add Zip Library, select the zip file you just downloaded and load into IDE. If you have already installed U8glib, please skip this step>įirst: Download U8glib library from OSOYOO U8glib library. Step 3)Install U8glib library into Arduino IDE. Unzip above file and run the installation program
#Darkside cc gen v1 driver#
If driver can not be installed automatically, you can download the driver from following link:
#Darkside cc gen v1 install#
Your pc should detect Arduino Mega2560 and install driver automatically. Step 2) use USB cable to connect Arduino Mega2560 and your PC.
Step 1) Install Arduino and driver (Please download the Arduino IDE version 1.5.X, you’d better download 1.5.4 version IDE).įirst, please download Arduino IDE from. If you do not follow above move, you can damage the control board and your 3D printer. Always double check power wire is properly installed. If you have only one Z axis servo, please connect it to Z slot, if you have two Z axis servos, another servo should be connected to E1.Ĭaution: do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can rmove static charge by touching metal tap). If you have only one Z axis servo, please connect it to Z_MOT slot, if you have two Z axis servos, another servo should be connected to E1_MOT. Please be noted MKS board Z axis servo controller installation as following:
#Darkside cc gen v1 how to#
(if you don’t know how to connect the circuit yet, check with your supplier or google the related topic). Please take following steps to install the software in order to let your printer work properly.ġ) Pls check the intalltion and connection graph link for MKS with 12864 or 2004LCDĢ) Pls check the intalltion and connection graph link for MKS with 2.8″ or 3.2″ TFT Touch LCD We can use same Marlin firmware for both boards. All other features of these two boards are same. MKS Base board integrated 5 servo control model which does not included in MKS Gen 1.4 board. MKS Board has following three sub-version: sub-version This board has integrated Arduino Mega2560 and Ramps1.4 control board and make the circuit installation much simpler than before. If your issue does not show up in either of the two places, please open a new issue describing the bug and steps to recreate it.MKS board is an control board for RepRap Prusa i3 3D compatible printer. If you found a bug, please check if it exists in the "known issues" sections of the readme in the github repo and the issues page to see if the issue exists or is known. (Requires restart after)Ĭhecks if a newer version of the script is available I found a bug! What do I do?
#Darkside cc gen v1 Patch#
It first stops AGSService, then deletes the AdobeGCClient folder.Īsk if the user wants to create a system restore point in case something goes wrong, then edit the registry to patch Acrobat.
0 kommentar(er)
